wintermute

Using a hot tub ozonation machine and UV aquarium filter for sanitation ATM. I have a sediment filter, but I have no confidence in it. I plan on building a sealed insulated box for the tub when I have some time in about 8 days or so. It's been going strong about 14 days now with an average temp of about 3c. The frost on the condenser melts fast and drains clean from the chiller.

The water smells good and is usually not cloudy. The ozonation clears up any cloudy water fast.

Still debating on parts for the box build, like a better filter system and new pump. I would rather keep both in the tub as to help with keeping things cold. The only filtration I have now come from that cheap sediment filter and that black aquarium sponge mesh. As of now I am having a hard time committing to a bulck head fitting that will be long enough to run from the tub to the outter wall with some of the fittings I have in mind that I can get in Germany that I can use for plumbing.

Parts are just a bit different in Germany. If y'all have suggestions, please send them via amazon.de as thats pretty reliable here.

Thanks for the input in advance!

      16 days later

      wintermute Very nice! I'm curious to see what you end up doing for the tub. Perhaps you could make your own longer bulkhead? If you can source any bulkhead you could cut it in half and extend it.

          11 days later

          wintermute

          Ok so I found a bulk head and made a basic wood frame and stuffed it to the brim with foam boards. Found a brass bulk head and fittings to connect it all and it's been very stable.

          Still waiting on a stronger pump to get to the manufacturer recommend flow rate of at least 1500 LPH, I am barely at like 700 ATM and I am sure that's affecting cooling.

          My only complaint so far is one. Tiny. Drip. Like do I have to disconnect everything again for this 1 drippy drop. 😑😑. And I know what it was, I lost the seal that came with the nipple shoes attachment, so I just cut down another rubber gasket to fit and replace it. And of course it's a leak. It's like a drop a minute so I just gotta let it go, especially as it's an outdoor setup. Still super irritating. I'll put some pics up later if your interested.

              Medicroger I would love to see some pictures. You definitely could use a stronger pump! About the leak, you could drain it a bit, seal it with silicone, and let it cure for 1-2 days if it bothers you enough. As long as it's not leaking inside the tub shell with the insulation you'll be fine like you said 🙂

                  My feet are kinda gross. Otherwise getting frustrated with pump performance. I bought two, an Oase and Aqqa, both advertised as 2.5kLPH pumps, I am not even touching 1k. I even tried it with out the filtration system attached.

                  I left the Oase attached as it has that German reliability behind it.

                  I only lost about 1LPM with out any filtration, so it's probably just the resistance of my plumbing network at play.

                  I did use hemp and Neo fermit paste on some of the seals and can see some residue from the sealing paste in the water as it gets submerged when I hop in. I am a tiny bit concerned about it, but it's non toxic, so there's that.

                  And I did take off the hose adapter and just dumped a bunch of silicone sealing glue and set it. Fixed the drip no problem. There is a good bit of water when I come in and out, but I would say its perfect enough. Other than the pump flow rate.

                  The flow rate is a slight concern as the chiller is rated for about 1.5k LPH minimum, but it does awesome with the slower flow rate.

                  I hope to find a pump that would better compliment the chill as it is by far the most expensive investment in this setup.

                  Either way. This took about 10+/- days. I would have GLADLY paid for a grizzly set up. I am just restricted on my Army base here in Germany for what I can actually acquire.

                  Looks great. I think you did a great job with what you had available. Even though the flow rate isn't as high as you wanted it appears to be still working fine so that's a win!

                  a month later

                  Bump for a question:

                  What's a good solution to help keep the water sanitized that won't hurt my current water chiller. I reached out to the manufacturer, and they haven't replied yet.

                  Also I intended to start using these water filters, but they are rated only to 5c. Not sure if it's a problem but would appreciate it if someone would let me know if it would be a problem.

                  6x Wessper 10" Wickel Kartusche... https://www.amazon.de/dp/B083V6Q9TV?ref=ppx_pop_mob_ap_share

                  Thanks for any input.

                    21 days later
                    a month later